Solutions To The Problems Of Fiat Panda Key Fob Replacement

Reasons Your fiat panda key replacement 500 Key Fob Won't Work

A key fob with the fiat 500 key replacement cost 500 number is a convenient way to open the doors and begin the car key cover fiat 500. There are many reasons why the fob won't work. These include a dead coin battery, damaged receiver module, water damage issues, and interfering.

This listing is for a NEW replacement fiat 500x key fob programming Flip Key Remote - similar to the Ilco brand that needs to be programmed professionally by a local automotive locksmith (click here for Locksmith Search). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

The most common reason your 500 key fob doesn't function is a dead battery. Modern key fobs have a limited range of operation and must be within just a few inches of the vehicle in order to function. If you are far from your vehicle and hit the keyfob, it will not respond and display the message "Key Fob Not Detected".

If this happens, simply replace the battery of your coin cell (Part number CR2032) by a new one from a reliable brand such as Panasonic, Duracell, or Energizer. You can usually find them at your local hardware store or on the internet.

You can test the battery in the coin-cell by pressing the buttons while standing near your Fiat Key Fob Not Working 500. The car will blink its parking lights, and the key fob should work the lock and unlock buttons.

If your fob's key isn't working after replacing the battery, there could be water damage that has prevented it from connecting to the module inside your vehicle. Water damage can happen in many ways, including the simple splash or submerging the key fob saltwater at the beach. If you suspect that your fob was exposed to water, put it in a dry rice bag to draw the moisture out. If that doesn't work your fob will probably need to be reprogrammed by an experienced locksmith or dealer.

Water Damage

The fob does have rubber seals to keep water out of the chip's electronic circuit and out of the ocean or washing it in a machine could cause water damage. Saltwater can cause the circuit board to short and then cease to function. It's not a good thing to let the fob get wet, but don't give it up when you accidentally drop it in water, or fail to take it out of your pants pocket.

First remove the battery from the fob. Before replacing the battery, clean the electronic chip with isopropyl, or a similar product. Check the fob to determine if it's working. If the key does not work, it may have to be changed. This is typically handled by a professional or dealer auto locksmith.

If the key you have is older and has not been programmed for your vehicle You will need to replace it completely. This is a simple procedure that can be completed by a professional locksmith for automotive use. The locksmith must cut the key to match the ignition on your vehicle. The locksmith also needs to program your fob into the vehicle's system. It's a simple and affordable process which can be completed in the same day.

Receiver Module Issues

Your 500 key fob may not work because it's out of range. The remote has a maximum range of 30 feet. Therefore, in the event that you are far away from your vehicle it won't respond to your commands. You can solve this issue by moving the remote closer to your car until it responds.

If your fob does not work after replacing the coin battery, also known as a "button", "watch" or "button" It could be due to a problem with the internal circuit board. Reprogramming the fob typically resolves the issue. You can find directions on how much is a new fiat 500 key to do this for the majority of vehicles by searching YouTube or looking through the owner's manual.

You may need to replace the metal retaining clips that hold the coin battery in place. If they lose tension it can prevent the battery from sitting properly, and this will result in the malfunction of your remote.

In rare instances the fob could be desync'd with your vehicle due to software problems or hardware issues. This could cause a significant headache, but you can often fix this by visiting a local dealer or auto locksmith to reprogram your fob for you. In some instances they may have to reinstall the software in your body control module, too.

Interference

In addition to a dead coin battery, the key fob may not be receiving or transmitting an signal due to interference. This could happen when the keyfob's location is in close proximity to a radio transmitter such as a cell phone or radar detector. Other reasons the key fob might not work could be due to a weak connection to the buttons and internal chip or water damage.

If your key fob suddenly stopped working, or you've tried everything at home to solve the issue (e.g. It could be a defective 500 receiver module after you've tried replacing the battery, reprogramming, and using an alternative key fob. The receiver module, located under the dashboard, is able to pick up radio frequency signals from your key fob. It converts them to electronic commands that the vehicle interprets.

Luckily, there is an easy method of resetting all of the on-board systems in your 500, including the key fob. Disconnect the battery for 15 minutes, removing first the negative cable and then the positive cable. Reconnect the battery. This will remove any remaining electricity, and restart the computer of your car. This could help you get your key fob to work again. If the problem persists you should speak with an expert technician. They can diagnose the exact cause of your issues.